AeroWolf oil-injected screw air compressor

Overview

On 16th Feb., 2019, AeroWolf international trading business held training for oil-injected screw air compressor , to analyze the advantage of AeroWolf oil-injected screw air compressor , so let us tell something about it. 1.Air end design analysis Profile design: the third generation ɑ model asymmetrical 5:6 tooth profile. a.Design pressure: 0.5Mpa~1.25Mpa b.Volume efficiency: ≥96% c.Rotor diameter and center distance:

Key Details

large d.Power consumption: ultra-low e.Transmission ratio: 1:1 f.Noise level: lower g.Sweden SKF bearing h.Max. operating temperature: 110℃ continuous running. 2.Electric Motor- S&L Brand Official Web: http://www.shfbdj.com S&L is also Ingersoll Rand China Factory’s Supplier. a. Fully enclosed 3Ph squirrel cage induction motor b. Starting method: Star delta starting c. Pole number: 2P d. IP Grade: IP54 e. SKF bearings made in Sweden f. Insulation Class: F class g. Efficiency: 95% according to Standard GB/T 1032 3.Radiator design a. Max. operating pressure: 1.7 Mpa b. Working temperature: 120 ℃ c. Ambient temperature: -20 ℃ ~ +60 ℃ d. Pressure loss: ≤

Practical Points

0.005 Mpa e. Temperature difference requirements: (1) Oil line: Oil inlet temperature – Oil outlet temperature ≥ 15℃ (2) Air line: Air outlet temperature ≤ ambient temperature + 15℃ f. Cooler fins: alternating expression. g. Material: Aluminum plate + copper h. Air line and oil line are separated. (only for 90 KW and above models)

What This Means for Buyers

Compressed air systems must be sized for the real air demand, not the maximum connected load. Oversizing wastes energy, while undersizing causes pressure drops and short cycling. A proper audit looks at flow in cubic meters per minute, working pressure in bar, duty cycle, ambient temperature and air quality class. Operators should record pressure, temperature and running hours daily. A small change in these readings often signals an issue before a failure occurs, which is cheaper to fix than an emergency repair.

How to Select the Right Equipment

Start with the actual air demand. Record the required flow, working pressure, voltage, ambient conditions and duty cycle, then add a safety margin. Match the compressor type to the application. A variable speed drive machine suits changing demand, while a fixed speed machine suits steady full load. For clean processes, an oil free unit or proper filtration is required.

Common Mistakes to Avoid

  • Sizing a compressor from the motor nameplate instead of measured flow.
  • Ignoring air quality and allowing water or oil into the system.
  • Skipping preventive maintenance and waiting for a breakdown.
  • Choosing the lowest price without comparing lifecycle energy cost.

Maintenance and Reliability

A routine service plan keeps output stable and protects the airend, motor and controls. Drain condensate, change filters on schedule, check belts and couplings, and inspect for leaks. A well maintained compressor holds its efficiency and avoids costly unplanned stops.

Next Steps

For help selecting or sizing a system, review the Screw Air Compressor and Compressed Air Solutions, or contact AeroWolf with your flow, pressure and air quality requirements.

A clear specification avoids expensive rework. Document the air quality class, the peak and average flow, the pressure band, the power supply and the expected operating hours before asking for a quote.

Compressed air is one of the most common utilities in a factory, yet it is often the least audited. A pressure of 0.1 bar above the requirement already adds measurable energy cost across a full year of operation.

Leakage is a hidden cost. Even a small leak wastes air around the clock. A regular walk through inspection with an ultrasonic detector finds leaks early and pays for itself quickly.

Ambient conditions change the output of a compressor. High intake temperature, high altitude and poor ventilation reduce flow, so the installation room should be cool, clean and well ventilated.

WhatsApp Email Phone